What is cutting in paint brush?

If you’ve ever seen painters working, you would understand how messy it can be to use improper painting techniques and tools. Cutting refers to the act of using a paint brush to reach areas that are too tight for paint rollers.

Such sites include the ceiling line, edges, corners, along baseboards and trim. The technique used for this is the cutting in the brush.

Every professional painter strives to load his brush and apply the paint properly to reduce dripping or splattering as much as possible. It goes a long way to keep the brush in good condition and also produce superb results.

What is the best brush for cutting in paint?

With a good paintbrush, painting a wall has never been much more comfortable. It is no cause for doubt that a good paintbrush enables you to apply paint around the edge of walls without any need for taping.

A good paintbrush is what guarantees good results. The best color in the universe can look appalling if applied with a low-quality paint brush.

According to paint brush experts, the best paintbrushes for cutting are average-sized paint brushes. Something along the lines of 2 inch to 2.5-inch broad sash brush has the right width suitable for painting an edge far-fetched for a roller.

The brush also possesses a very narrow handle, making it very comfortable to hold. You can work with it for a long time without getting sores on your hands.

You can get this brush from some of your favorite brands. It will make your painting more comfortable, faster, and will pay off in the long term.

When is the best time to do cutting-in paint?

Painting experts recommend that you cut in paint before rolling when painting. It sounds relatively easy and reasonable to do, right? However, there are rare situations where it is ideal for cutting in first.

A professional with an appropriate length of experience is in the best position to make such a decision.

Why you should cut in Before Rolling on paint

Cutting in paint before rolling enables you to paint up to all the exterior edges or corners of the wall or ceiling you are trying to paint. The width of the area you cut has a lot to do with the width of the brush.

Using a 4-inch wide paint brush will offer a broader edging than a 2-inch wide brush would do. Except, of course you use the 2-inch brush painting two layers to increase the cutting in width.

Cutting in ensures there is little chance of you running the roller into the ceiling or a wall with a color that differs.
Most persons prefer to have a border, so a prior cutting offers them the edge to work.

Should your cut in dry before you roll?

Your cut in paint doesn’t have to dry before you roll. If the paint is still wet and brush marks are visible, there are chances that you will roll over and adjust the thicker paint that might have brush lines when rolling.

Depending on how large the area you are cutting in and if you are by yourself, the color might dry regardless by the time you get to rolling. If two people are painting, then the roller can start as soon as there is enough space to get to work.

When is it okay to cut in after rolling?

If the inside corners of a wall where both sides of the border are the same color of what you are painting, then it’s fair to cut in after rolling. It will save you time as rolling goes much quicker than brushwork.

When you are priming walls and ceilings, it is okay to roll first. Regardless of where you are painting, all of the paint should be a white primer for new drywall. Even if you are using ceiling paint, it should match up nicely.

How can I cut without leaving brush marks?

Brush marks usually occur as a result of over brushing. However, the most common error people are prone to make is not thinning the paint.

Some latex paint that is right out of the gallon is a compromise between how thick it should be so as not to spatter when rolled and how thick it needs to be to allow brush strokes to self-level by itself.

Load the brush with latex paint and remove it off the brush bristle into a can. Do this several times to accumulate some paint in the can.

You can now add 15 to 20 percent water and stir with the brush. Then try painting with that, and remember not to brush over paint that’s still drying.

AND, if you have high-quality brushes, you need to take good care of them. Before painting with latex paint, wash the paint brush out in the water. If you are using the brush for oil-based paint, wash it off in a thinner.

Here, the concept is to understand that some wet paint will move up the “heel” of the brush as you are painting, where the bristles are very tight and almost do not change position as you do the painting.

Any paint that goes up there will dry as you paint. This results in the accumulation of dry paint in the paint brush heel, thereby damaging the brush.

Therefore, washing the brush out with water or paint thinner first, you fill all those tiny capillaries between the bristles in the brush’s heel with the paint thinner.

So, when paint gets up there, it doesn’t dry but stays wet. So, when it is time to wash out the paint brushes, not only does it wash out faster, it washes out much more thoroughly.

The technique to cut in paint

It would help if you had enough lighting in the area. Cutting in is meant to be done with care.
Don’t try to apply too much paint, and a smooth, even coat will look best.

Some colors will not cover with just one coat. Cutting in after a second roll is sometimes faster than trying to make one coat cover.

Masking tape is good for only inaccessible points.

While coming to the wall with a loaded paint brush, begin painting an inch or more away from the edge. You can then start to paint up to the edge with more strokes. That is to say, don’t take a brush that is full up toward the edge. Instead, paint up to the edge as the paint flows out of the brush.

When cutting in next to a ceiling with texture, a straight line edge may be required. It is good to use a small stiff slot screwdriver tip to scrape away a narrow path from the corner’s texture. Then cut in up to this edge.

Cutting-in does take practice. A good cut in job dramatically improves the look of a painted room. A professional look is possible; use these tips mixed with some practice and patience.

Some Painting Tips for Cutting in

Get a good cutting in brush

The cheap brush you picked up from the store may seem to have been a good bargain, but will it serve you well in the long run? I believe you want something that will last. Get a good quality brush that will make your painting work hassle-free.

Paint the ceiling first

When painting, do not be tempted to start with the walls, except that you don’t intend to paint the ceiling. This is to make sure you don’t have to worry about paint dripping on the wall while cutting in around the ceiling in a straight line afterward.

Let the ceiling dry before cutting in on the walls.

After painting the ceiling, give it some extra time to dry up before painting the walls.

Have a damp cloth nearby

If you are a newbie in the painting who want to grow fast, you may likely get paint dabs on the ceiling while working on the walls. A damp cloth nearby will come in handy when you want or have the need to wipe the paint off the ceiling arises.

Final Words

In conclusion, getting the best cutting in brush available is necessary for any painter who wants to deliver impeccable jobs.

To master the art of cutting in paint, you need to practice a lot as it’s much more difficult than painting regular flat surfaces.

You should also read our article on What Paint Roller To Use For A Smooth Finish.